cra12e, cra12s www.vishay.com vishay revision: 24-jun-13 1 document number: 31003 for technical questions, contact: thickfilmchip@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 thick film chip resistor array fetaures ? convex terminal array av ailable with either scalloped corners (e vers ion) or square corners (s version) ? wide ohmic range: 10r to 1m0 ? 8 or 10 terminal package with isolated resistors ? pure tin solder contacts on ni barrier layer, provides compatibility with lead (pb)-free and lead containing soldering processes ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 note (1) power rating depends on the max. temperature at the solder point, the component placement density and the substrate material. note (2) preferred way for ordering product s is by use of the part number. standard electrical specifications model circuit power rating p 70 c w limiting element voltage max. v ? temperature coefficient ppm/k tolerance % resistance range ? series cra12e ? cra12s 01; 02; 20 0.100 50 100 1 10 to 1m e24; e96 03 0.125 200 2; 5 10 to 1m e24 zero-ohm-resistor: r max. = 50 m ? , i max. = 1.5 a technical sepcifications parameter unit cra12e and cra12s circuit 01; 02; 20 cra12e and cra12s circuit 03 rated dissipation at p 70 (1) w per element 0.1 0.125 limiting element voltage ? u max. ac/dc v50 insulation voltage u ins (1 min) v 100 insulation resistance ? > 10 9 category temperature range c - 55 to + 155 part number and product description part number: cra12e08347k0jtr (2) model terminal style pin circuit value tolerance packaging special cra12 s e 08 10 1 = 01 2 = 02 3 = 03 8 = 20 r = decimal k = thousand m = million 0000 = 0 ? jumper f = 1 % g = 2 % j = 5 % z = 0 ? jumper tr up to 2 digits tl product description: cra12e 08 03 47k 5 % rb8 e3 cra12e 08 03 47k 5% rb8 e3 model pin circuit resistance value tolerance packaging lead (pb)-free cra12e cra12s 08 10 01 02 03 20 10r = 10 ? 47k = 47 k ? 1m = 1m ? 0r0 = jumper 1 % 2 % 5 % rb8 rd7 e3 = pure tin termination finish a12e 834 0 cr jr k 0t 7
cra12e, cra12s www.vishay.com vishay revision: 24-jun-13 2 document number: 31003 for technical questions, contact: thickfilmchip@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 circuit available types and ranges model terminal count circuit temperature coefficient tolerance cra12s 10 01 02 03 20 100 ppm/k 200 ppm/k 1 %; 2 %; 5 % cra12e 08 01 02 03 20 10 packaging model tape width diameter pitch pieces/reel blister tape acc. iec 60286-3, type ii part number product description cra12e 08 ? cra12e 10 ? cra12s 10 12 mm 180 mm/7" 330 mm/13" 8 mm 2000 5000 tr tl rb8 rd7 pin 1 10 pin 02 circuit pin 1 8 pin 10 pin 01 circuit 03 circuit 20 circuit pin 1 8 pin 10 pin
cra12e, cra12s www.vishay.com vishay revision: 24-jun-13 3 document number: 31003 for technical questions, contact: thickfilmchip@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 derating dimensions - 55 - 25 0 25 50 75 100 125 155 175 120 100 8 0 60 40 20 0 70 ambient temperature in c fraction of rated dissipation in % w e a a a e b c d p b t a l pin 1 w b* a* p 1 0 3 s-version w a b c p b t a l pin 1 w b* a* p 1 0 3 e-version model pin no # dimensions in millimeters laa*bb*ptw cra12e 8 5.08 0.79 - 0.51 0.38 1.27 0.55 3.05 cra12e 10 6.40 0.79 - 0.51 0.38 1.27 0.55 3.05 cra12s 10 6.40 0.79 0.89 0.51 0.38 1.27 0.55 3.05 tol. 0.15 0.15 0.15 0.25 0.2 0.1 0.15 0.15 solder pad dimensions in millimeters cwdp a b e wave 2.2 4.3 0.57 1.27 0.71 1.05 1.09 reflow 2.2 3.9 0.57 1.27 0.71 0.86 1.09
cra12e, cra12s www.vishay.com vishay revision: 24-jun-13 4 document number: 31003 for technical questions, contact: thickfilmchip@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note (1) figures are given for a single element. all tests are carried out in accordance with the following specifications: ? en 60115-1, generic specification ? en 140400, sectional specification ? en 140401-802, detail specification ? iec 60068-2 environmental test procedures packaging of components is done in paper or blister ta pes according to iec 60286-3 test procedures and requirements en 60115-1 clause iec 60068-2 test method test procedure requirements permissible change ( ? r ) (1) stability class 1 or better stability class 2 or better stability for product type: 10 ? to 1 m ? cra12e/cra12s 4.5 - resistance - 1 % 2 %, 5 % 4.7 - voltage proof u = 1.4 x u ins ; 60 s no flashover or breakdown 4.13 - short time overload ?? 2 x u max . ; ? duration according to style (0.25 % r + 0.05 ? ) (0.5 % r + 0.05 ? ) 4.17.2 58 (td) solderability solder bath method; sn60pb40; non-activated flux; (235 5) c; (2 0.2) s good tinning ( ? 95 % covered) no visible damage solder bath method; sn96.5ag3cu0.5; non-activated flux; (245 5) c; (3 0.3) s good tinning ( ? 95 % covered) no visible damage 4.8.4.2 - temperature coefficient (20/- 55/20) c and (20/125/20) c 100 ppm/k 200 ppm/k 4.32 21 (u u3 ) shear (adhesion) 45 n no visible damage 4.33 21 (u u1 ) substrate bending d epth 2 mm; 3 times no visibl e damage, no open circuit in bent position (0.25 % r + 0.05 ? ) 4.19 14 (na) rapid change of temperature 30 min. at - 55 c; 30 min at 125 c 5 cycles 1000 cycles (0.25 % r + 0.05 ? ) (1 % r + 0.05 ? ) (0.5 % r + 0.05 ? ) (1 % r + 0.05 ? ) 4.23 - dry heat - (1 % r + 0.05 ? ) (2 % r + 0.1 ? ) 4.23.2 2 (ba) damp heat, cyclic 125 c; 16 h 4.23.3 30 (db) cold 55 c; ? 90 % rh; 24 h; 1 cycle 4.23.4 1 (aa) low air pressure - 55 c; 2 h 4.23.5 13 (m) - 1 kpa; (25 10) c; 1 h 4.23.6 30 (db) damp heat, cyclic 55 c; ? 90 % rh; 24 h; 5 cycle 4.23.7 - dc load 4.25.1 - endurance at 70 c 1.5 h on; 0.5 h off; 70 c; 1000 h 70 c; 8000 h (1 % r + 0.05 ? ) (2 % r + 0.1 ? ) (2 % r + 0.1 ? ) (4 % r + 0.1 ? ) 4.18.2 58 (td) resistance to soldering heat solder bath method; (260 5) c; (10 1) s (0.25 % r + 0.05 ? ) (0.5 % r + 0.05 ? ) 4.35 - flammability, needle flame test iec 60695-11-5; 10 s no burning after 30 s 4.24 78 (cab) damp heat, steady state (40 2) c; (93 3) % rh; 56 days (1 % r + 0.05 ? ) 4.25.3 - endurance at upper category temperature 155 c; 1000 h (1 % r + 0.05 ? ) (2 % r + 0.1 ? ) 4.40 - electrostatic discharge (human body model) iec 61340-3-1; 3 positive and 3 negative discharges; esd voltage: 500 v (1 % r + 0.05 ? ) 4.29 45 (xa) component solvent re sistance isopropyl alcohol; 50 c; method 2 no visible damage 4.30 45 (xa) solvent resistance of marking isopropyl alcohol; 50 c; method 1; toothbrush marking legible, no visible damage 4.22 6 (fc) vibration, endurance by sweeping f = 10 hz to 2000 hz; x, y, z ? 1.5 mm; a ? 200 m/s 2 ; 10 sweeps per axis (0.25 % r + 0.05 ? ) (0.5 % r + 0.05 ? ) 4.37 - periodic electric overload 0.1 s on; 2.5 s off; 1000 cycles (1 % r + 0.05 ? ) 4.27 - single pulse high voltage overload, 10 s/700 s 10 pulses (1 % r + 0.05 ? ) u 2.5 x p 70 x r = up 70 x r = u p 70 x r u max. ? = u 15 x p 70 x r 2 x u max. ? = ? 10 x p 70 x r 2 x u max. ? =
legal disclaimer notice www.vishay.com vishay revision: 08-feb-17 1 document number: 91000 disclaimer ? all product, product specifications and data ar e subject to change with out notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of th e products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product , (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all implied warranties, includ ing warranties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain types of applicatio ns are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular applic ation. it is the customers responsibility to validate tha t a particular product with the prope rties described in the product sp ecification is suitable for use in a particular application. parameters provided in datasheets and / or specifications may vary in different ap plications and perfor mance may vary over time. all operating parameters, including ty pical parameters, must be va lidated for each customer application by the customer s technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product could result in personal injury or death. customers using or selling vishay product s not expressly indicated for use in such applications do so at their own risk. please contact authorized vishay personnel to obtain writ ten terms and conditions rega rding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners. ? 2017 vishay intertechnology, inc. all rights reserved
|
